Salsbury-industries 3786 Combination Lock Manuel d'utilisateur télécharger pdf

SALSBURY INDUSTRIES

1010 East 62

Street, Los Angeles, CA 90001-1598

Phone: 1-800-624-5269 Int’l Phone: 323-846-6700

Fax: 1-800-624-5299 Int’l Fax: 323-846-6800

www.mailboxes.com engineering@mailboxes.com

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Combination Locks - 2086, 2286, 2486, 3486, 3686, 3786

Operation & Change Instructions

Combination Factory Setting

Make sure the dial knob “0” is aligned with the proper hub number 1,

2, 3, or 4 on the lock body hub. The factory hub number is marked

on the upper left corner of the label on the rear of the lock. The

factory hub number position results in the combination number

setting that is marked on the rear label. See illustration.

To Operate The Lock

There is an index to which the dial number is aligned on both the lock

body and the front of the door to which the lock is fastened.

1. Turn dial to left (CCW - counterclockwise) at least four times

and stop when first number is aligned with index.

2. Turn dial to right (CW - clockwise) passing first number and stop

when second number is aligned with index.

3. Turn dial to left (CCW) and stop when third number is aligned

with index.

4. Turn dial firmly to right (CW) to open lock while pulling door

open.

IMPORTANT: If any combination number is turned past the index,

the entire series of numbers must be redialed starting with 1 above.

To Change Combination Number

1. From the rear of the door and lock, remove the two screws

fastening lock to door. Do not remove the two smaller screws

holding the cover on the rear of the lock.

2. Check that the dial knob is positioned at the proper factory-set

hub number (see above) with the dial “0” aligned with the index.

3. Remove the dial knob and rotate dial to “25” on opposite side of

dial and reinsert dial knob into lock shaft. This will set the dial

knob at a new hub number opposite the previous setting.

4. Reinstall lock to rear of door with the two screws.

5. While looking through the peephole in the back of the lock, turn

dial to the left (CCW) at least four times and stop when the slot

in the first wheel (the one nearest the lock cover) comes in line

with the peephole. Note that there are two slots in the first

wheel. Look for the larger of the two. Read and record the first

dial number at the index.

6. Turn dial slowly to the right (CW) until the second wheel slot

comes in line with the first wheel slot and the peephole. Record

the second dial number at the index.

7. Turn dial slowly to the left (CCW) until the fence in the peephole

drops into the two slots in the first and second wheels. Record

the third dial number at the index.

8. Turn the dial firmly to the right (CW) to open lock. If the lock

does not operate, carefully repeat steps 1 thru 7 above.

CAUTION: Before closing door, test new setting several times.

DO NOT LUBRICATE THIS LOCK.

Résumé du contenu

Page 1 - To Change Combination Number

SALSBURY INDUSTRIES 1010 East 62nd Street, Los Angeles, CA 90001-1598 Phone: 1-800-624-5269 Int’l Phone: 323-846-6700 Fax: 1-800-624-5299

Commentaires sur ces manuels

Pas de commentaire

Salsbury-industries 3786 Combination Lock Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Meubles Salsbury-industries 3786 Combination Lock. Salsbury Industries 3786 Combination Lock User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Meubles Salsbury-industries 3786 Combination Lock