Salsbury-industries 1512 Series Large Commercial Signage Manuel d'utilisateur télécharger pdf

Large Commercial Signage - 1511/1512 Series

Assembly & Installation Instructions

Thank you for selecting Salsbury Industries’ 1511 or 1512 series large commercial post mounted signage. We are confident that the quality and

construction of this product will provide years of maintenance free use. These instructions are designed to assist you in a typical installation.

Preliminary Notes

There are three basic steps to assembly and installation:

1. Assemble the posts.

2. Install the sign into the posts assembly.

3. Install the posts and sign assembly into the ground.

Assembly

First check to see that all the parts and fasteners in the carton have

been located and identified according to illustration 6 on a following

page. Also refer to the all of the illustrations to position the parts

correctly.

Note that there are two (2) different types of right-angle brackets.

There are four (4) of each type. One type has two (2) round

threaded nuts installed in the short leg; the other type does not.

Assembly may proceed more easily if all the bolts and screws are not

fully tightened until primary assembly has been completed.

1. Set the two 4” square x 80” long posts on their sides on a flat

surface. The factory-attached U-channels should be facing each

other. See illustration 1.

Illustration 1

2. Attach one of each of the two (2) types of right-angle brackets to

each post with two (2) 5/16” x 5” long hex head bolts. The two (2)

right-angle brackets with the installed nuts mount on the inside of the

4” square by 80” vertical posts; the other two (2) mount on the

outside of the posts. The bolts are installed from the outside of each

post through the short leg of one outside bracket, through the 4”

square post, and then into the nuts installed in the short leg of the

inside bracket. The long leg of the right-angle brackets should be

positioned toward the bottom end of the 80” post.

3. Attach one of the 3-1/2” square x 40” long cross arms to the two

(2) inside right-angle brackets. The U-channel should be facing up or

toward the finial ends of the 80” posts. Use two (2) 1/4”-20 x 1/2”

long flat-head screws in each end of the cross arm to fasten the

cross arm to the right angle brackets.

4. Attach two (2) of the right-angle brackets with installed round

threaded nuts inside the other 3-1/2” square x 40” long cross arm

with two (2) 1/4”-20 x 1/2” long flat-headed screws for each bracket.

The short leg of each bracket should be flush with each end of the

cross arm. See illustration 2.

Illustration 2

SALSBURY INDUSTRIES

1010 East 62

Street, Los Angeles, CA 90001-1598

Phone: 1-800-624-5269 Int’l Phone: 323-846-6700

Fax: 1-800-624-5299 Int’l Fax: 323-846-6800

www.mailboxes.com engineering

@mailboxes.com

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

1 2 3

Résumé du contenu

Page 1 - Illustration 2

Large Commercial Signage - 1511/1512 Series Assembly & Installation Instructions Thank you for selecting Salsbury Industries’ 1511 or 1512 se

Page 2 - Illustration 5

Large Commercial Signage - 1511/1512 Series Assembly & Installation Instructions 6. Slide the signage panel into the two (2) opposing U-chan

Page 3 - Signage Into Concrete

Large Commercial Signage - 1511/1512 Series Assembly & Installation Instructions Illustration 6 Installing the In-Ground Mounted Posts for t

Commentaires sur ces manuels

Pas de commentaire

Salsbury-industries 1512 Series Large Commercial Signage Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Meubles Salsbury-industries 1512 Series Large Commercial Signage. Salsbury Industries 1512 Series Large Commercial Signage User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Meubles Salsbury-industries 1512 Series Large Commercial Signage